background image

GPS05 Module

User manual
Release 1.01

 

 

www.aim-sportline.com

 

21

4

5 – GPS Manager software 

GPS Manager

 is the software properly designed by 

AIM 

to communicate lap and 

split positions to 

EVO4

MyChron4

MXL

EVO3

 

Pro/Pista 

(

GPS Module

 equipped) 

and to 

SmartyCam, 

the only on-board camera with GPS and data overlay. For 

further information refer to GPS Manager user manual that can be downloaded 
from 

www.aim-sportline.com

, download area software section. 

1 8

5.1 – Typical use of GPS Manager 

Typical use of 

GPS Manager

 software implies going on the track with 

GPS05 

Module

 connected to AIM logger and setting lap and splits (if configured). Afterwards 

GPS05 Module

 can record lap and split times of the track forever. 

To copy lap/splits configuration from one 

GPS05 Module

 to another,: 

 Connect 

GPS05 Module

 (1) to the PC 

 Run 

GPS Manager

 software 

  Press “Connect” button 

  Press “<<” button to copy the configuration in the PC database 

 Disconnect 

GPS05 Module

 (1) from the PC 

 Connect 

GPS05 Module

 (2) to the PC 

  Press “Connect” button 

  Press “>>” button to copy the configuration from the PC database to the 

local copy of 

GPS05 Module

 configurations 

  Press “Transmit” button. 

Summary of Contents for GPS05 Module

































Reviews: