background image

9

The  crossed  out  wheelie  bin  symbol  that  is  on  your 
product indicates that this product should not be disposed 
of  via  the  normal  household  waste  stream.  Proper 
disposal will prevent possible harm to the environment or 
to  human  health.  When  disposing  of  this  product  please 
separate it from other waste streams to ensure that it can 
be  recycled  in  an  environmentally  sound  manner.  For 
more  details  on  collection  and  proper  disposal,  please 
contact your local government office or the retailer where 
you purchased this product.

Ei Electronics, Shannon, Co. Clare, Ireland

Nominal activation conditions/ sensitivity,
response delay (response time) and
performance under fire condition

Pass

Operational reliability

Pass

Tolerance to voltage supply

Pass

Response delay and temperature resistance

Pass

Vibration resistance

Pass

Humidity resistance

Pass

Corrosion resistance

Pass

Electrical stability

The Declaration of Performance No. 15-0005 may be consulted
at www.eielectronics.com/compliance

Pass

15

DoP No.15-0005

EN14604:2005 + AC:2008

Smoke Alarm Devices:

Ei161e, Ei166e

Heat Alarm Devices:

Ei164e

Fire Safety

0086

 

Summary of Contents for Ei160e Series





















Reviews: