AHT Cooling Systems GmbH
40
2 Product description
2.1
General information
AHT products comply with EU Directive 2011/65/EU
(RoHS2) for the prevention of hazardous substances
in electrical and electronic devices and EU
regulation 1907/2006 (REACH) on the registration,
evaluation and approval of chemicals.
In the product design, the manufacturer has
considered the environmental and disposal-
friendliness of the device, in particular, for the
refrigerant propane (R-290) and the propellant
pentane (for the insulating foam). Propane does not
have any ozone depletion potential (ODP) and only
a very low greenhouse potential (GWP) of 3.
The refrigerant R-134a is recorded in the Kyoto
Protocol. It does not have any ozone depletion
potential (ODP) and has a greenhouse potential
(GWP) of 1430.
2.2
Technical data
Important technical data can be found on the power
rating plate (see
→
Chapter 2.2.1).
External
dimensions
See → Device models overview.
Airborne noise
emissions
Emission sound pressure level <
70 dB(A)
Maximum load
on storage racks
-
See → following table and
Chapter 9.1
- Sticker at the top right of the
inside of the equipment cover
next to the power rating plate
Storage rack
Maximum load
[kg/m²]
Standard shelf/display shelf
115
Heavy-load shelf/display
shelf
250
Floor plate/floor shelf
600
Technical interfaces:
Power supply
Device-specific; observe
the specifications on the
power rating plate (see
→
2.2.1).
- 3 x 380-420V 50Hz /N/P or
- 3-pin 4 wire ground
208-240 V/ 60 Hz
Connector types
Device connection for
devices < 150g R-290
and R-134a devices
Device connection for
devices > 150g R-290
- 3 x 380-420V 50Hz /N/P:
CEE 5x16A
- 3-pin 4 wire ground
208-240 V/ 60 Hz:
NEMA L15-20P + main
switch in power cord
Fixed connection with
terminal (protection class
IP54)
Minimum requirement
for connection cable
Minimum cross-section
2.5 mm² (14AWG)
Condensation water
connection
DN 40
Communication
AHT Inter Cabinet BUS (ICB)
Bus cable
CAT 5-S/FTP
(PIN 1-8
assigned)
Brine connection
Dutch screw connection
3/4“
(Forward/reverse running)
Light/night blind
control
(Control of external
day/night signal)
Floating contact via market
light signal box (accessory).
For devices of type R 290:
The control signal for the
market light signal box must
be coupled with an isolation
transformer to the market
lighting separated from the
mains.
Electrical protection
(see
→
Chapter 7.2):
All combinations must be created in 3-pin format.
Fuses
Rated
current
[A]
Triggering
characteristics
Type
Fault
current
[mA]
for
208-
240V
for
380-
420V
LS
(MCB)
20
16
C
(time-lag)
_
_
FI
(RCCB)
≥ 40
≥ 40
_
G
(surge current-
resistant)
30
FI-LS
(RCBO)
20
16
C
(time-lag)
G
(surge current-
resistant)
30
If you need more information, do not hesitate to contact
the maintenance services (see
→
Chapter 10.4).
Technical specifications are subject to change
without notice.
2.2.1
Power rating plate and serial number
When handling the device, the information on the
"power rating plate" must be observed. This is found
on a sticker at the top right inside of the device cover
and contains important technical data about
- device name and device type,
- serial number,
- Climate class (see
→
Chapter 2.3),
- Rated voltage and frequency,
- rated current and rated consumption,
- Refrigerant and amount used,
- Net content,
- Date of manufacture,
- Test mark,
- Technical data for the interior lighting (optional),
- and other technical data.
2.3 Intended use
The devices are only suitable for packaged,
refrigerated food products.
NOTICE
•
Property
damage
due to improper use.
►
Do not operate the device outside the indicated
climate category conditions (ambient
temperature, relative humidity).
►
The ambient temperature must not be less than
16°C (60.8°F).
