manualshive.com logo in svg

Agrimate AM-708T, User Manual

Share
Download
Agrimate AM-708T User Manual Download Page 4

4

SYMBOLS IN THE MANUAL

(1)   Read owner’s manual before operating this machine.
(2)   Wear head, eye and ear protection.
(3)   Wear foot protection.
(4)   Wear gloves.
(5)   Warning / Attention

Never modify your machine. We won’t warrant the machine, if you use the remodeled 

power sprayer or if you don’t observe the proper usage written in the manual

 

 

WARNING

Failure to observe the precaution may result in the risk of death or serious injury.

!

 

IMPORTANT

Failure to observe the precaution may result in damage or mal function of the product.

 

NOTE

Other additional explanations that may be of use when operating the product.

For safe operation and maintenance, symbols are carved in relief on the machine. According to 

these indications, please be careful not to make a mistake.

 

The port to refuel the “MIX GASOLINE” 

Position:

 FUEL TANK CAP

 

The direction to close the choke 

Position:

 AIR CLEANER COVER

 

The direction to open the choke 

Position:

 AIR CLEANER COVER

WARNINGS IN THE MANUAL

SYMBOLS ON THE MACHINE

Summary of Contents for AM-708T







































Reviews:

No comments

Brands by name

Popular brands

Load more brands