manualshive.com logo in svg

Agrimate AM-708T, User Manual

Share
Download
Agrimate AM-708T User Manual Download Page 3

3

* When nozzle (supplied) is attached. 

** Nozzle and back belt are not included. 

Due to product improvements, these specifications are subject to change without notice.

SPECIFICATION

Model name & number

AM-708T Knapsack Motorised Sprayer

Purpose

Spraying agricultural chemicals and cold 

water for pest control, weeding, and 

growth control

Dry weight * (kg)

9.8

External dimensions of main unit (length x 

width x height)** (mm)

335x390x640

Capacity of chemical fluid tank (litres)

25

Capacity of fuel tank (litres)

0.9

Pump

Type

Plunger type

Speed (rpm)

1739

Spray output Normal (MPa)

0.5 - 3.5

Maximum (MPa)

3.5

Maximum water absorption (litres/

min) 

47.0

Motor transmission system

Centrifugal clutch

Engine

Type

Single-cylinder air-cooled 2-cycle gasoline 

engine

Engine number

AM262

Exhaust capacity (cc)

25.6

Fuel used

Lubricating oil/gasoline mix

Lubricating oil used

2-cycle engine oil

Admixture ratio

Gasoline 50 : Oil 1 (when using  FC grade 

genuine oil)

 Carburetor

Diaphragm

Ignition system

CDI

Spark plugs

CMR7H

Starter system

Recoil starter type

Stopping system

Primary cable short circuit

Air cleaner

Dry type

Summary of Contents for AM-708T







































Reviews:

No comments

Brands by name

Popular brands

Load more brands