manualshive.com logo in svg

Agrimate AM-708T, User Manual

Share
Download
Agrimate AM-708T User Manual Download Page 25

25

Case 1. Starting failure 

CHECK 

PROBABLE CAUSES 

ACTION

fuel tank 

∅ 

incorrect fuel 

∅

 drain it and use correct fuel

fuel filter 

∅

 fuel filter is clogged 

∅

 clean

carburetor adjustment screw 

∅

 out of normal range 

∅ 

adjust to normal range

sparking (no spark) 

∅

 spark plug is fouled/wet 

∅

 clean/dry

 

∅

 plug gap is incorrect 

∅

 correct (GAP: 0.6 to 0.7 mm)

spark plug 

∅

 disconnected 

∅

 retighten

Case 2. Engine starts but does not keep running/hard re-starting

CHECK 

PROBABLE CAUSES 

ACTION

fuel tank 

∅ 

incorrect fuel or staled fuel 

∅

 drain it and use correct fuel

carburetor adjustment screw 

∅

 out of normal range 

∅

 adjust to normal range

muffler, cylinder (exhaust port) 

∅

 carbon is built-up 

∅

 wipe away

air cleaner 

∅

 clogged with dust 

∅

 wash

cylinder fin, fan cover 

∅

 clogged with dust 

∅

 clean

When your unit seems to need further service, please consult with our  service shop in your area.

TROUBLESHOOTING GUIDE 

Summary of Contents for AM-708T







































Reviews:

No comments

Brands by name

Popular brands

Load more brands