manualshive.com logo in svg

Agria 5100 Rabbit, Original Operating Instructions, Page: 7 / 48

Share
Download
Agria 5100 Rabbit Original Operating Instructions Download Page 7

agria

 Grassland Mower 5100

7

Unpacking and Assembly

1 Steering column pin
2 Steering handle
3 Clips
4 Linch pin
5 Washer
6 Electric cable with connector

(on steering handle)

7 Electric connector on engine
8 Bowden cables
9 Guide hook for Bowden cables

Unpacking

l

Open the top of the cardboard box.

l

Cut the box open on all four corners

and fold down the sides.

Assembly of steering handle

l

Push the steering handle location

holes (2) onto the steering column pin
(1).

l

Fit the washer (5) onto the steering

column pin (1).

l

Lock the steering handle by fitting the

linch pin (4) through the horizontal hole
in the steering column.

l

Notch the steering handle into the

middle position of the side adjustment
mechanism (see page 18).

l

Adjust the steering handle to the de-

sired working height (see page 18).

l

Connect the electric cable (7) to

socket (6) (engine safety circuit system).

l

Fit the Bowden cables (8) into the

guide hook (9).

l

Inspect again all cable guides to en-

sure the cables are not twisted or
jammed and to avoid clutch problems.

l

Attach Bowden and electric cables

with clips (3) to the steering handle.

Attaching the cutter bar

See instructions on page 20

Starting up

See instructions on page 23

Summary of Contents for 5100 Rabbit

















































Reviews:

No comments