manualshive.com logo in svg

Agria 5100 Rabbit, Original Operating Instructions, Page: 33 / 48

Share
Download
Agria 5100 Rabbit Original Operating Instructions Download Page 33

agria

 Grassland Mower 5100

33

5. Maintenance

Fuel strainer

2

1

1

5

Fuel System

l

Each time you maintain the machine,

check fuel hose, fuel tank, and carbure-
tor for leakages and repair, if necessary.
Immediately replace leaking or porous
fuel hoses.

l

Replace fuel hoses after every 2

years.

l

Clean the fuel  tank at 100-hour in-

tervals.

è

 - 

Service

ç

l

Clean the fuel strainer at 100-hour

intervals.

To do this, drain all fuel into a suitable
container.

Clean the fuel strainer with a cleaning
solvent and inspect it for damage.

Replace the fuel strainer.

è

 - 

Service

ç

Excessive Fuel Supply

l

After excessive fuel supply to the en-

gine, remove the spark plug, clean and
dry it. Then crank the engine with the
recoil starter a number of times. After-
wards screw the spark plug in and move
the speed control lever to "VOLLGAS"/
"FULL THROTTLE". Then start the en-
gine via the recoil starter.

Summary of Contents for 5100 Rabbit

















































Reviews:

No comments