manualshive.com logo in svg

Agria 5100 Rabbit, Original Operating Instructions, Page: 32 / 48

Share
Download
Agria 5100 Rabbit Original Operating Instructions Download Page 32

32

agria

 Grassland Mower 5100

5. Maintenance

1 Air filter cover
2 Snap mechanism
3 Filter element
4 Latches

5

5

Air Filter

Clean the air filter insert at 3-month in-
tervals but not later than 25 operating
hours (earlier in very dusty conditions).
To do this, proceed as follows:

l

Clean the air filter and its surround-

ing area.

l

Open the snap mechanism (2), fold

down the filter cover (1) and remove it.

l

Remove the paper element (3).

l

Tap the element against a smooth

surface or blow compressed air against
the inside of the filter.

Never brush the filter because this
would press the dirt into the fibres.

l

Replace the filter element if it is ex-

tremely dirty.

l

Inspect the filter element carefully for

holes or other damage and replace it if
necessary.

l

Replace the filter element

l

Attach the cover and snap the latches

(4) into place.

I

Do not wash the paper element
(tap it or blow it out)

Summary of Contents for 5100 Rabbit

















































Reviews:

No comments