manualshive.com logo in svg

Agilent Technologies G8610 Series, Field Installation Instructions

Share
Download
Agilent Technologies G8610 Series Field Installation Instructions Download Page 9

Vacuum Products Division 

Manual 699910005, Hot Ion Source Replacement

 

 

Page 4

 

 

 

1.2.3

 

O-ring Care 

When removing, checking, or replacing O-rings, keep in mind the following: 

NOTE 

 

Agilent recommends replacing all O-rings during routine maintenance or 
during any maintenance procedure requiring that O-rings be removed. 

CAUTION 

 

 

Remove O-rings carefully with your fingers. Do not use metal tools for 
this task; this prevents scratching of any sealing surfaces. 

•

 

Wipe all O-rings clean with a lint-free cloth before installation to 
ensure that no foreign matter is present to impair the seal. 

•

 

Do not use grease or any other substance on O-rings that will 
come in contact with the vacuum surfaces. 

•

 

Do not use alcohol, methanol or other solvents on O-rings. Doing 
so causes deterioration and reduces their ability to hold a 
vacuum. 

•

 

Agilent does not recommend the use of vacuum grease. If 
applicable, apply a small amount of Apiezon® L grease and wipe 
the O-rings shiny dry. 

 

1.2.4

 

Metal Seal Care 

CAUTION 

 

 

Metal Seals must be replaced any time a spectrometer is opened. All 
fasteners must be installed and torqued per assembly procedure 
specifications. Remove Metal Seals carefully with your fingers or a soft 
tool. Metal tools scratch sealing surfaces. 

•

 

Metal Seals are supplied in pre-cleaned condition. No cleaning is 
required. If necessary, Metal Seals can be cleaned using the 
recommended solvents. Wipe Metal Seals clean with a lint-free 
cloth before installation to ensure that no foreign matter impairs 
the seal. 

•

 

Do not use grease or any other substance on Metal Seals that 
will come in contact with the spectrometer. 

 

 

 

Summary of Contents for G8610 Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands