manualshive.com logo in svg

Agilent Technologies G3440-68011, Installation Instructions Manual

Share
Download
Agilent Technologies G3440-68011 Installation Instructions Manual Download Page 8

8

Installation Instructions

Agilent G3440-68011 Micro Electron Capture (µECD) 3rd Detector

Figure 8

MSD heated zone cable included in main communication grommet

9

Route the MSD heated zone cable behind the inlet fan and down the left 
side of the GC. Include it in the grommet as shown in 

Figure 10

 on page 10.

10

Connect the third detector heated zone cable to the open end of the MSD 
heated zone cable (on the side of the GC). See 

Figure 10

 on page 10.

11

Connect the 

EPC5

 female connector of the third detector communications 

cable to the matching 

EPC5

 connector on the main communications harness. 

The 

EPC5

 connector is typically located in EPC bay 5. See 

Figure 9

 on 

page 9. You may need to lift any PCM or Aux EPC module to access 

EPC5

 on 

the main harness. 

12

Connect the 

Aux Det1

 female connector of the third detector 

communications cable to the matching 

Aux Det1 

connector on the main 

communications harness. 

Aux Det1

 is located in the back inlet EPC bay. 

As an example, shown in 

Figure 9

, is a TCD EPC communications cable 

connection and routing.

MSD heated zone 
cable

Grommet

Summary of Contents for G3440-68011



























Reviews:

No comments

Brands by name

Popular brands

Load more brands