manualshive.com logo in svg

Agilent Technologies G1369C, User Manual, Page: 58 / 66

Share
Download
Agilent Technologies G1369C User Manual Download Page 58

58

G1369C LAN Interface User Manual

3

Getting  Help

Firmware Update

Firmware Update

The LAN Interface Card’s firmware can be updated, using the firmware 
provided by the Agilent support web side. A procedure will be provided 
with the firmware.

Initial firmware revision: B.06.40 (for 

“Hosted Module Support”

on 

page 51)

Updates may be required in case the 

“Hosted Module Support”

on page 51 

requires an update (only when this feature is used). For normal LAN 
operation firmware changes may not be required.

For the G1369C LAN card a more convenient firmware update mechanism 
is available that replaces the old Telnet procedure. PLease refer to the 
LAN/RS- 232 Firmware Updated Tool (version 2.9 or later).

Update Procedure

1

Download the actual firmware from the Agilent web 
http://www.chem.agilent.com/scripts/cag_firmware.asp?nmod=LC

2

The zipped firmware archive contains all required files and the 
procedure for the update.

3

Follow the provided instructions.

WA R N I N G

Do not load G1369C firmware on a G1369B card! The G1369B card will become 
inoperable.

Summary of Contents for G1369C



































































Reviews:

No comments