manualshive.com logo in svg

Agilent Technologies G1369C, User Manual, Page: 52 / 66

Share
Download
Agilent Technologies G1369C User Manual Download Page 52

52

G1369C LAN Interface User Manual

2

Getting  Started

Hosted Module Support

How to connect hosted modules

•

All modules must be on the same FW level (A/B/C.06.32 or A/B/C.06.50 
or later). No mixed revisions possible! See additional information in 
section 

“Firmware Update”

on page 58.

•

Install the G1369C LAN Card in a module with LAN card slot 
(preferentially a detector, e.g. G1314C).

•

Establish a CAN connection between G1369C LAN card and the module 
which holds the LAN card.

•

Connect the hosted module to a free CAN connector in the stack.

•

Maximum 3 hosted modules can be connected to the stack.

Figure 43

How to connect hosted modules

N O T E

In 1100/1200/1260/1290 systems, the LAN Interface Card should be installed in the 
detector (DAD, MWD, FLD, VWD, RID) due to its higher data handling rate. If no 
1100/1200/1260 detector available, use the pump or the autosampler (in this order).

Hosted 
Module

G1369C LAN Card

Detector

Summary of Contents for G1369C



































































Reviews:

No comments