manualshive.com logo in svg

Agilent Technologies G1369C, User Manual, Page: 46 / 66

Share
Download
Agilent Technologies G1369C User Manual Download Page 46

46

G1369C LAN Interface User Manual

2

Getting  Started

Manual Configuration

(LAN Interface Card Status Page). The information corresponds to the 
information in 

Figure 28

 on page 41.

Figure 34

LAN Interface Card Status Page

In 

Figure 35

 on page 46 the complete listing is shown. For explanations 

refer to 

Figure 28

 on page 41.

Figure 35

LAN Interface Card Status Page (complete)

Agilent Technologies G1369C

FW Revision   : B.06.40 0003

MAC Address   : 0030d31b8417

--------------------------------

Init Mode     : Bootp

--------------------------------

TCP/IP Properties

- active -

IP Address    : 0.0.0.0

Subnet Mask   : not specified

Def. Gateway  : not specified

- stored -

IP Address    : 134.40.24.160

Subnet Mask   : 255.255.248.0

Def. Gateway  : 134.40.24.1

--------------------------------

TCP/IP Status : Error

Bootp timeout

--------------------------------

Controller    : not connected

Summary of Contents for G1369C



































































Reviews:

No comments