Agilent Technologies 5977B CI MSD Operating Manual Download Page 204

Page: 204 / 254

General Maintenance



To Clean an EI XTR, SS, or Inert Source

204

5977B Series MSD Operating Manual

To Clean an EI XTR, SS, or Inert Source

Materials needed

•

Abrasive paper (5061-5896)

•

Alumina abrasive powder (8660-0791)

•

Aluminum foil, clean

•

Cloths, clean (05980-60051)

•

Cotton swabs (5080-5400)

•

Glass beakers, 500 mL

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Solvents

•

Acetone, reagent grade

•

Methanol, reagent grade

•

Methylene chloride, reagent grade

•

Ultrasonic bath

Preparation

Disassemble the ion source. (See

“To Disassemble the EI SS or EI Inert

Source”

on page 198 or

“To Disassemble the EI XTR Source”

on page 201.)

Collect the following parts to be cleaned for an EI SS or Inert source: (See

Figure 66

on page 206.)

•

Repeller

•

Interface socket

•

Source body

•

Repeller block insert

•

Drawout plate

•

Drawout cylinder

•

Ion focus lens

•

Entrance lens

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands