Agilent Technologies 5977B CI MSD Operating Manual Download Page 198

Page: 198 / 254

General Maintenance



To Disassemble the EI SS or EI Inert Source

198

5977B Series MSD Operating Manual

To Disassemble the EI SS or EI Inert Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Hex ball driver, 2.0 mm (8710-1804)

•

Wrench, open-end, 10 mm (8710-2353)

Procedure

Refer to the exploded parts view

Figure 64

and the EI SS and EI Inert parts list

Table 20

on page 199 while using this procedure.

Remove the EI source. (See

“To Remove the EI HES”

on page 178 or

“To

Remove the EI XTR, SS, or Inert Source”

on page 196.)

Remove the two gold plated screws from the filaments and remove the
filaments from the source.

Loosen the two gold plated screws from the source heater block assembly,
and separate the repeller assembly from the source body. The repeller
assembly includes the source heater block assembly, repeller, and related
parts.

Remove the repeller nut and washers then remove the repeller from the
source heater block assembly.

Remove the repeller insulators and the repeller block insert from the source
heater block assembly.

Remove the gold plated setscrew from the side of the source body.

Push on the drawout plate to remove the entrance lens, ion focus lens,
drawout cylinder, and drawout plate from the other end of the source body.

Unscrew the interface socket. A 10-mm open-end wrench fits the flats on the
interface socket.

Remove the entrance lens and ion focus lens from the lens insulator.





Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands