manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

7

General Maintenance

To Remove the EI HES

178

5977B Series MSD Operating Manual

To Remove the EI HES

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Tweezers (8710-2460)

Procedure

1

Vent the MSD. (See 

“To Vent the MSD” 

on page 136.) 

2

Open the analyzer chamber. (See 

“To Open the Analyzer Chamber” 

on 

page 176.)

3

Remove the two large thumbscrews that hold the ion source in place. (See 

Figure 55

 on page 179.)

4

Disconnect the wires from the EI HES. (See 

Figure 55

 on page 179.) Do not 

bend the wires any more than necessary. (See 

“To Connect/Disconnect 

Wiring to the EI HES” 

on page 180.)

WARNING

The analyzers, GC/MSD interface, and other components in the analyzer 
chamber operate at very high temperatures. Do not touch any part until you 
are sure it is cool.

CAUTION

Always wear clean gloves to prevent contamination when working in the 
analyzer chamber.

CAUTION

Make sure you use an antistatic wrist strap and take other antistatic 
precautions before touching analyzer components.

CAUTION

When disconnecting leads, pull on the connectors, not on the wires.

    

             

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

vacuubrand BVC control Instruction Manual preview
BVC control
Brand: vacuubrand Pages: 76
Atlantic Ingenio VM 050 D400-3-E Instruction Manual preview
Ingenio VM 050 D400-3-E
Brand: Atlantic Pages: 69
ProMinent Sigma 2 S2Ca Operating Instructions Manual preview
Sigma 2 S2Ca
Brand: ProMinent Pages: 77
CTC Union 588347301 Installation And Maintenance Manual preview
588347301
Brand: CTC Union Pages: 28
salmson SXE-DXE Installation And Starting Instructions preview
SXE-DXE
Brand: salmson Pages: 28
Calorex Pro-Pac 30 Technical Manual preview
Pro-Pac 30
Brand: Calorex Pages: 24
Yardworks YW65PHP Instruction Manual preview
YW65PHP
Brand: Yardworks Pages: 19
ICP PHF Series Installation Instructions Manual preview
PHF Series
Brand: ICP Pages: 16
GE Zoneline AZ91H18E E Series Owner'S Manual preview
Zoneline AZ91H18E E Series
Brand: GE Pages: 78
ubbink PoolFilter Manual preview
PoolFilter
Brand: ubbink Pages: 40
Geotech Geopump I Series Installation And Operation Manual preview
Geopump I Series
Brand: Geotech Pages: 16
Wahl Bach marey PP4 Instruction Manual preview
marey PP4
Brand: Wahl Bach Pages: 12
Nalco 3D TRASAR Series Installation And Operation Manual preview
3D TRASAR Series
Brand: Nalco Pages: 243
SAINT-GOBAIN PFD1 AstiPure Operating Instructions Manual preview
PFD1 AstiPure
Brand: SAINT-GOBAIN Pages: 19
Logitex LX ACDC/M+K 100 A Operating And Installation Manual preview
LX ACDC/M+K 100 A
Brand: Logitex Pages: 18
Little Giant 10EC-CIA-SFS Installation Manual preview
10EC-CIA-SFS
Brand: Little Giant Pages: 16
Reefe VSRM Series User Manual preview
VSRM Series
Brand: Reefe Pages: 14
Grundfos MQ 3-35 Installation And Operating Instructions Manual preview
MQ 3-35
Brand: Grundfos Pages: 60

Brands by name

Popular brands

Load more brands