Agilent Technologies 5977B CI MSD Operating Manual Download Page 201 | Manualshive

Page: 201 / 254

background image

7

General Maintenance



To Disassemble the EI XTR Source

5977B Series MSD Operating Manual

201

To Disassemble the EI XTR Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Hex ball driver, 2.0 mm (8710-1804)

•

Wrench, open-end, 10 mm (8710-2353)

Procedure

Refer to the exploded parts view

and the EI EXT parts list

page 202 while using this procedure.

1

Remove the EI XTR source. (See

“To Remove the EI XTR, SS, or Inert

2

Remove the filaments by removing the two gold plated screws and
separating the filaments from the source.

3

Loosen the two gold plated screws on the source heater block assembly, and
separate the repeller assembly from the source body. The repeller assembly
includes the source heater block assembly, repeller, and related parts.

4

Remove the gold plated setscrews from the side of the source body.

5

Pull the entrance lens and ion focus lens to remove them from the source
body.

6

Remove the extractor lens and insulator.

7

Separate the entrance lens and ion focus lens from the lens insulator.

8

Remove the repeller nut, washers, and insulator from the front side of the
source heater block assembly, then remove the repeller, insulator, and
repeller block insert from the opposite side.

«
...
199
200
201
202
203
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: A.O. Smith Pages: 56

Zoneline AZ85H09DAC

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: Water Worker Pages: 24

Brand: Walchem Pages: 31

Brand: Carrier Pages: 30

Brand: Envision Pages: 36

Brand: Atlantic Pages: 20

Point-of-Use Drinking Water System

Brand: R-Can Pages: 12

NKVE MCE Series

Brand: DAB Pages: 72

FlexxPump 250 OLED

Brand: DLS Pages: 80

POWER VENTED GAS FIRED WATER HEATER

Brand: GSW Pages: 39

URG250H6N-475-264

Brand: Bradford White Pages: 32

Brand: ITS Telecom Pages: 20

INTERGAS Altherma EJHA-AV3

Brand: Daikin Pages: 36

AHLSTAR 2.15 Series

Brand: Sulzer Pages: 122

Brand: RHOSS Pages: 344

Digital-Flo DFS1540

Brand: Armstrong Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands