Agilent Technologies 4072A Advanced Pre-Installation Manual Download Page 64

Page: 64 / 84

Chapter 4

Agilent 4072/4073 Preinstallation Guide, Edition 4

Receiving

Unpacking Testhead

This section covers how to unpack the testhead. The testhead is stored in the carton. Remove the carton using the
following procedure.

CAUTION

At least two person are required to move the testhead.

1. Cut the nylon straps securing the box, remove the

tape, and open the top of the carton.

2. Remove the top cover.

3. Remove the carton on the testhead.

4. The testhead is wrapped in a vinyl cover. Do

not

remove the vinyl cover while the testhead is
outside of the clean room.

5. Take the testhead to the clean room.

CAUTION

The testhead must adapt to the atmospheric temperature before removing the carton. Also,
measure the atmospheric temperature at the location where the testhead will reside.

Summary of Contents for 4072A Advanced





















































































Search results

Summary of Contents for 4072A Advanced

Reviews:

Related manuals for 4072A Advanced

Brands by name

Popular brands

Agilent Technologies 4072A Advanced, Pre-Installation Manual

Search results

Summary of Contents for 4072A Advanced

Reviews:

Related manuals for 4072A Advanced

Brands by name

Popular brands