Agilent Technologies 4072A Advanced Pre-Installation Manual Download Page 33

Page: 33 / 84

Chapter 2

Agilent 4072/4073 Preinstallation Guide, Edition 4

Site Preparation

Safety Precautions

Figure 2-15 shows the dimensions of the bottom of the system cabinet. The figure shows the form and the position
of casters and leveling feet.

Figure 2-15

Dimensions of system cabinet bottom

When the testhead is placed beside the manual wafer prober, strap the testhead to a table as shown in Figure 2-16.
Use suitable belts to secure the testhead according to the shape of the table.

Figure 2-16

Securing testhead

After an earthquake, confirm the system operation as follows:

1. Check the system visually for damage or disconnected parts.

2. Turn on the system and confirm that the tester starts correctly.

3. Execute the diagnostic program (diag4070) and check the measurement capability of the tester.

LEFT

Leveling foot

Caster

BOTTOM

Leveling foot (4 place)

Belt

Table

Testhead

Manual
Wafer Prober

Summary of Contents for 4072A Advanced





















































































Search results

Summary of Contents for 4072A Advanced

Reviews:

Related manuals for 4072A Advanced

Brands by name

Popular brands

Agilent Technologies 4072A Advanced, Pre-Installation Manual

Search results

Summary of Contents for 4072A Advanced

Reviews:

Related manuals for 4072A Advanced

Brands by name

Popular brands