manualshive.com logo in svg

AGI Westeel EasyFlow2 100 Series, Assembly & Installation Manual

Share
Download
AGI Westeel EasyFlow2 100 Series Assembly & Installation Manual Download Page 20

20

BU-0101704 R3

4.5. Bin Wall Cutout

An opening must be cut in the bin wall for the underfloor auger.

Cutting an opening in the bin can weaken the bin’s structure and may lead to bin collapse if
the instructions in this section are not accurately followed.

When installing the bin unload, consult the manufacturer for specific details on the bin wall cutout.

General points to consider are:

• Keep a minimum 45° angle between the center points of any two openings, such as an aeration fan (see

Figure 3

).

Figure 3.

Minimum Angle Between Openings

• Center the opening in the middle of the bin sheet, between two vertical bolt seams.

• Do not cut an opening through a vertical bolt seam between two sheets or a stiffener position.

• Cut the opening in a bin sheet at a location designated for discharge (see

Figure 4

and

Table 8

).

Note

When measuring the opening, measure the dimension for the height of the cutout from the bottom
edge of the bin wall sheet.

• Cut the opening as tight as possible for the underfloor auger to pass through and do not have more than a

1/4” (6 mm) gap to the auger joint flange on any side.

• The vertical flange of the bottom bin angle may be cut flush to the sides of the opening to allow the

underfloor auger to fit through the opening.

4. PREPARATION

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

Summary of Contents for Westeel EasyFlow2 100 Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands