AGI Westeel EasyFlow2 100 Series Assembly & Installation Manual Download

Page: 21 / 74

BU-0101704 R3

Table 8.

Bin Wall Cutout Dimensions

Tube Diameter

Height of Opening (Y)

(From the bottom the

bin sheet)

Width of Opening (X)

8-in

11-3/4” (300mm)

15-1/4” (390mm)

10-in

12-1/2” (320mm)

15-1/4” (390mm)

Figure 4.

Bin Wall Cutout

4.6. Retrofit Information

When retrofitting the unload system into an existing bin:

1. Clean up and remove all settled grain dust deposits and ensure the air is nearly free of dust.

Sparks from grinding and hammer strikes which contact settled grain dust deposits or dusty
air present a risk of explosion.

2. Temporarily remove the floor planks (if equipped) which will be used to cover the bin unload from the bin

wall cutout to past the bin center point.

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

4. PREPARATION

Summary of Contents for Westeel EasyFlow2 100 Series











































































Search results

Summary of Contents for Westeel EasyFlow2 100 Series

Reviews:

Related manuals for Westeel EasyFlow2 100 Series

Brands by name

Popular brands

AGI Westeel EasyFlow2 100 Series, Assembly & Installation Manual

Search results

Summary of Contents for Westeel EasyFlow2 100 Series

Reviews:

Related manuals for Westeel EasyFlow2 100 Series

Brands by name

Popular brands