AGI EZTest Hazmon Manual Download | Manualshive

Page: 28 / 33

background image

mDT001 HazMon System Tester Technical Manual /23

CMC INDUSTRIAL ELECTRONICS LTD
Phone: (604) 421-4425 Toll Free: (888) 421-4425 Fax: (604) 421-7734

www.cmciel.com [email protected]

The Industry Leader in HazMon Technology

3.8

Cable Insert Test CMC internal use only

The Cable Insert Test function detects how many DS28EA00 sensors connected on the cable.

1. Prepare a mDC001 hardware board installed the mDC001F firmware.

2. Connect the cable tested to the first cable connector.

3. Connect mDT001 Easy Tester with the mDC001 board.

4.

Turn on mDT001 Easy Tester, and choose “Cable Insert Test function”

5. Press

<Select>

button, and wait for a while, it will show the number of sensors

connected on the cable.

«
...
26
27
28
29
30
...
»

Summary of Contents for EZTest Hazmon


































Reviews:

No comments

Related manuals for EZTest Hazmon

Brand: Laica Pages: 4

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: RayLight Pages: 34

GAZELLE FREESTYLE

Brand: Gazelle Pages: 10

Brand: Latham Pages: 19

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: U-Line Pages: 6

Brand: Wang Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands