manualshive.com logo in svg

AGI EZTest Hazmon, Manual

Share
Download
AGI EZTest Hazmon Manual Download Page 11

 

mDT001 HazMon System Tester Technical Manual /6 

 

CMC INDUSTRIAL ELECTRONICS LTD 
Phone:  (604) 421-4425  Toll Free:  (888) 421-4425  Fax:  (604) 421-7734 

www.cmciel.com   [email protected]

 

 

The Industry Leader in HazMon Technology

 

 

 

3.1  Using the Menu Control Pushbuttons 

 

There are four menu control pushbuttons: 

 

Select 

Select the displayed function 

Back 

Go back one menu level or exit this function 

Down 

Next menu item 

Up 

Previous menu item 

 

There are six menu selections from the main menu. These are selected using the 

Up

 and 

Down

 pushbuttons.  

 

Sensor Test 

Test an individual sensor 

Bus Test 

Test the 

CMC Intrinsically Safe network

 

Sensor Emulator 

Emulates connected sensor 

Sensor Configuration 

Configure sensor parameters 

Battery Voltage 

Check remaining battery level 

Proximity Data 

Read proximity data for mCP001 Sensor 

     Cable Insert Test 

Read number of sensors connected on the 
cable insertion FOR CMC INTERNAL USE 
ONLY 

 

Once the function is displayed, it is executed by pressing the 

<Select>

 pushbutton. 

Summary of Contents for EZTest Hazmon


































Reviews:

No comments

Brands by name

Popular brands

Load more brands