background image

FCC Information

FCC Information

FCC Information

FCC Information

7/11/2003

3

FCC Notice

FCC Notice

FCC Notice

FCC Notice

RF Exposure (For 200mW units only: Part Numbers CL200 & CL200A)

RF Exposure (For 200mW units only: Part Numbers CL200 & CL200A)

RF Exposure (For 200mW units only: Part Numbers CL200 & CL200A)

RF Exposure (For 200mW units only: Part Numbers CL200 & CL200A)

 WARNING:

 WARNING:

 WARNING:

 WARNING:  This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful
interference and (2) This device must accept any interference received,
including interference that may cause undesired operation.

 WARNING:  

 WARNING:  

 WARNING:  

 WARNING:  To satisfy FCC RF exposure requirements for mobile and base station

transmitting devices, a separation distance of 32cm or more should be
maintained between the antenna of this device and persons during
operation.  To ensure compliance, operations at closer than this distance is
not recommended.

The preceding statement must be included as a CAUTION statement in
manuals for OEM products to alert users on FCC RF Exposure compliance.

Summary of Contents for ConnexLink





















Reviews: