6
E
nglish
Congratulations on your purchase of the Aermec WMT10
control panel with
thermostat. Made of materials of superior quality in strict compliance with
the safety regulations, the WMT10 is easy to use and will have a long life.
CHARACTERISTICS
FUNCTIONS
The thermostat maintains the temperature set for the room.
The
WMT10
control panel has the following functions:
- cursor to choose the Cooling functioning mode, Off or
Heating;
- manual season change;
- manual choice of the ventilation speed;
- desired room temperature selection (+10°C÷30°C)
- operation of systems with 2 pipes
- operation of systems with 4 pipes
- operation of systems with 2 pipes (cooling) + electric heater
(heating)
- thermostat-controlled ventilation;
- continuous ventilation;
- continuous ventilation in Cooling mode and thermostat-
controlled ventilation in Heating mode;
- when it switches on, it starts the fan coil keeping the settings
that were active before the previous switch-off;
- after a power failure, the fan coil restarts keeping the settings
that were active before the switch-off;
- air temperature probe incorporated in the panel;
MANUAL
CHANGE OVER
Manual selection of the desired functioning mode (Cooling or
Heating) with the cursor.
For correct operation, before selecting a functioning mode,
check that the water circulating in the system is at a suitable
temperature for the desired functioning mode.
In case of heating with electric heater, the fan coil must be
electrically powered.
VENTILATION
Three-speed ventilation check, can be selected manually.
The ventilation mode is set in the installation phase, by
operating the circuit card mobile Jumper (see the image).
CONTINUOUS VENTILATION
The ventilation continues to work even if the set temperature
is reached, so the temperature is therefore checked by opening
and closing the water valve(s) fitted in the system.
Do not use this setting in systems without water shut-off
valves, as ventilation will be continuous, and not controlled
by the thermostat.
THERMOSTAT-CONTROLLED VENTILATION
The ventilation switches off automatically when the set
temperature is reached.
CONTINUOUS VENTILATION IN COOLING MODE AND
THERMOSTAT-CONTROLLED VENTILATION IN HEATING
MODE
Ventilation in cooling functioning mode is adjusted differently
from ventilation in the heating mode:
- Cooling (Continuous Ventilation)
- Heating (Thermostat-controlled Ventilation)
The
WMT10
regulating thermostat is a control panel for fan
coils, to be mounted on the wall.
Controls the operating functions of the fan coil according to
the set mode. The panel must be wall-mounted; it is used in
systems with 4 tubes, 2 tubes and 2 tubes with resistance, with
the possibility of connecting two On-Off valves to shut off the
water feeding the coils.
The panel is electrically protected by an internal fuse.
The ventilation mode operation is chosen in the installation
phase with Jumper.
Each panel can directly control a single fan coil.
The control panel only consists of mains voltage (230V)
electrical circuits; all the inputs must therefore be properly
insulated for this voltage.
The valve servo controls must also be suitable for 230V.
WMT10 must only be installed by expert personnel.
Disconnect the power supply before beginning any installation
or maintenance operation. Risk of electrocution if live
components are touched.
CONNECTION CABLES SPECIFICATIONS
Use H05V-K or N07V-K type cables with 300/500 V with
insulation, piped or ducted.
Use cables with double H05W-F type insulation for
installations with cable in sight.
TECHNICAL SPECIFICATIONS:
Power supply: 230V (± 10%)
Input power: 1.5VA
Adjustable temperature range: 10°C - 30°C
Differential: 1°C
Ambient working conditions: 0°C ÷ 60°C with relative
humidity 10% ÷ 90%, without condensation.
Ambient storage conditions: -18°C ÷ 60°C with relative
humidity 10% ÷ 90%, without condensation.
Material: ABS UL94 V0
Colour: RAL9016
Complies with:
Low Voltage directives 73/23 (EN 60730-1, EN 60730-2-9, EN
60335-1);
Electromagnetic compatibility 89/336 (EN 61000-4-1, EN
55011, 55022, 55014);
ITS UL783.
