manualshive.com logo in svg

AERMEC Omnia HL 11 CM, Technical And Installation Booklet

Share
Download
AERMEC Omnia HL 11 CM Technical And Installation Booklet Download Page 38

HL L   DIPSWITC

H CONFIGURATION

Sw 1

ON

OFF

Sw 2

Dipswitch 1 (Default OFF)

Thermostatic temperature control:
- for operation at modulated power, set to OFF
- for 3-level operation, set to ON

Dipswitch 2 (Default OFF)

Adjustment band:
- for standard, set to OFF
- for extended, set to ON

Dipswitch 3 (Default ON)

Louver control:
- for manual control, set to OFF
- for motorised control, set to ON

Dipswitch 4 (Default OFF)

Probe correction:
- for dynamic correction of values, set to OFF
- for fixed correction of values, set to ON

Dipswitch 5 (Default OFF)

Enable heating mode according to water temperature:
- for normal heating mode (39°C), set to OFF
- for reduced Heating (35°C), set to ON

Dipswitch 6 (Default OFF)

Enable cooling mode according to water temperature:
- for normal cooling mode (17°C), set to OFF
- for reduced cooling (22°C), set to ON

SETTING OF THE CONTROL PANEL DIP-SWITCH

Configuration of dipswitches must only be carried out by qualified personnel during unit installation.
Always disconnect the power supply before performing this operation.
Adjust the dipswitches inside the thermostat for the following functions:

DRIVER BOARD DIP-SWITCH CONFIGURATION

Power the unit down. Configuration of dipswitches must only be carried out by qualified personnel during unit installation.

Dip 1 (Default OFF )

Dip 2 (Default OFF )

Preset in factory

Fin opening management:

-Complete opening (wall-mount installations), OFF.
-Reduced opening (recess installations), ON.

Sw 2

Dip 1 (Default OFF )

Preset in factory

Dip 2 (Default OFF )

Preset in factory

Dip 3 (Default OFF)

Preset in factory

Dip 4 (Default OFF)

Preset in factory

*

*

*

*

*

*

ON

OFF

1

2

3 4

5

6

Sw 1

*

*

*

*

ON

OFF

1

2

3 4

Sw 2

*

*

ON

OFF

1

2

Sw

=

*

Thermostatic control with Modulated Power

Normal regulation band

Normal Cooling Enabling (water 17°C)

Normal Heating Enabling (water 39°C)

Dynamic Probe Correction

Manual slat management

Pre-calibrated in the factory

Pre-calibrated in the factory

Pre-calibrated in the factory

Pre-calibrated in the factory

Wide regulation band

Motorised slat management

Fixed probe correction Warm (4°C)

Reduced Heating Enabling (water 35°C)

Reduced Cooling Enabling (water 22°C)

Three step thermostat control

Factory settings

Reduced opening of the slat (recess installation)

Complete opening of the slat (wall-mounted installation)

Pre-calibrated in the factory

Driver Card

Summary of Contents for Omnia HL 11 CM



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands