AERMEC BHP Series User Manual Download Page 40

Page: 40 / 44

Label Error

Description

Code

Comp. stalling

Indicates that the compressor is currently stalled

Overtemp. mod.

Indicates that an overtemperature has been detected on a component

(heatsink, IPM or PFC)

T mod. sensor

Indicates that an error has been detected on the temperature sensor for a

component (heatsink, IPM or PFC)

Charge circuit

Indicates an error on the charging circuit

AC voltage

Indicates a power supply error

Temp driver

Indicates an error affecting the external air sensor

AC contactor

Indicates a protection status on the power supply

Temp. drift

Indicates a protection status for drift temperature

Sensor con.

Indicates a protection status for the sensor monitoring the phases

ODU Com.

Indicates a serial communication error between the display and the out-

door unit

Temp RGL

Indicates an error affecting the temperature sensor on the cooling circuit

gas line

Temp RLL

Indicates an error affecting the temperature sensor on the cooling circuit

fluid line

Summary of Contents for BHP Series













































Search results

Summary of Contents for BHP Series

Reviews:

Related manuals for BHP Series

Brands by name

Popular brands

AERMEC BHP Series, User Manual

Search results

Summary of Contents for BHP Series

Reviews:

Related manuals for BHP Series

Brands by name

Popular brands