background image

USER MANUAL 

EarthGuard – EG-300 

Australian Energy Research Labs 

AER013 – Rev 1.1 

21st July 2020

 

AER013 REV 1.1 

 

About Australian Energy Research Laboratories 

Australian Energy Research Laboratories (AERL) was founded by Stuart Watkinson (BE Elec. Eng., Grad. M.I.E.A) in 
1985 to commercialize the “Power Optimizer”, a revolutionary solution to a complex problem, developed while 
studying at the University of Queensland in Brisbane, Australia. 
 
Unlike many inventors, Stuart possessed not only a great idea, but also the entrepreneurial skill to turn it in to a 
commercially viable product.  The “Power Optimizer” would eventually come to be known as the AERL 
MAXIMIZER™, the world’s first truly Universal Maximum Power Point Tracker (MPPT). 
 
Today, AERL manufactures a range of highly reliable and efficient specialised power electronic controllers for use in 
Solar, Micro Hydro, Micro Wind and Cathodic Protection applications. 
 

Contact Information  

Address:  

Unit 15, 1015 Nudgee Rd,  
Banyo, QLD, 4078, Australia 
 

Phone:   

+61 07 3129 0330

 

Email:    

[email protected]

 

Website: 

https://www.aerl.com.au

 

Disclaimer  

UNLESS SPECIFICALLY AGREED TO IN WRITING, AUSTRALIAN ENERGY RESEARCH LABORATORIES:  

(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR 
OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.  

(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT, 
CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION.  

THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.  

Notice of Copyright  

EarthGuard Owner’s Manual © 2020 by Australian Energy Research Laboratories Pty. Ltd. All Rights Reserved.  

Trademark  

AERL and the AERL logo are trademarks owned and used by Australian Energy Research Laboratories Pty. Ltd.  

These trademarks may be registered in Australia and other countries.  

Effective Date  

July 2020 (07/2020) 

 

 

 

 

 

Summary of Contents for EarthGuard EG-300
















Reviews: