Aerco 5R5-384 User Manual Download

Page: 98 / 139

AERCO Control System (ACS)

APPENDIX B:

Status and Fault Messages

Page 98 of 139

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, New York 10913

11/22/2017

GF-131

Phone: 800-526-0288

OMM-0081_0F

B.5 BCM

(BOILER COMMUNICATION MODULE)

FAULT CODES

TABLE B-5: BCM (Boiler Control Module) Fault Codes

Code

Description

Effect

Correction

Reset

Boiler Pipe is frozen.
FlowSensor temp. is
36°F or less.

Ignition is
inhibited. Pump
runs for 5 min at
max speed.

Carefully
defrost boiler

AUTOMATIC - when
FlowSensor is greater than
41°F.

Maximum Δ-
temperature protection.
Flow temperature -
Return Temperature >
Water

Δ-Temp

Prot 50°F

All burners turned
OFF and Pump
ON at maximum
speed.

Check the
system
installation.

AUTOMATIC - when

Δ-

temperature < Water Δ-
Temp Protection.

High outlet
temperature.
FlowSensor
temperature > 203°F.

All burners turned
OFF and Pump
ON at maximum
speed.

Check Flow
Sensor or
system pump

AUTOMATIC - when
FlowSensor < 176°F.

Settings Corrupted

Ignition is
inhibited. Pump
runs for 5 min at
max speed.

Re-program
the settings.
Contact
Factory

MANUAL - push reset
switch or cycle power.

Internal Failure

Ignition is
inhibited.

Contact
Factory for
new BCM.

MANUAL - cycle the power.

FlowSensor fault.

All burners turned
OFF.

Check flow
sensor or
wiring.

AUTOMATIC

Standby. No remote
control detected and
Request input is open.

Ignition is
inhibited.

Close Request
input for
Manual
operation.

MANUAL - push reset
switch or cycle power.

No BMM detected.

Ignition is not
possible.

Check the
BMM eBus
wiring.

MANUAL - push reset
switch or cycle power.

Summary of Contents for 5R5-384












































































































































Search results

Summary of Contents for 5R5-384

Reviews:

Related manuals for 5R5-384

Brands by name

Popular brands

Aerco 5R5-384, User Manual

Search results

Summary of Contents for 5R5-384

Reviews:

Related manuals for 5R5-384

Brands by name

Popular brands