AEQ PHOENIX ALIO User Manual Download Page 71 | Manualshive

Page: 71 / 91

AEQ PHOENIX ALIO User Manual Download Page 71

AEQ

PHOENIX ALIO

71

7. A user ID and password are requested (by default, both are aeq). After you have

correctly entered these two items, the firmware upgrading screen will be displayed.

Firmware upgrading screen detail

8. Check to see whether the versions displayed are the same as the firmware that is

currently in effect. If they do not match, upgrade the firmware as indicated below.

9. Select the module you want to upgrade in "Upgrade" column. NOTE: Each upgrading

file is specifically designed to upgrade a specific module within the unit: CPU, DSP or
FPGA.

10. In "Select file" enter the access route to the upgrade file containing the new firmware

version, using the "Seleccionar archivo" button.

11.  Press the "Upgrade" button in the lower part of the screen.
12.  Wait for on-screen confirmation that the operation has been successfully completed.
13.  In  the  Internet  browser,  go  to  the  UPGRADE  section  and  ensure  that  all  the  firmware

versions installed in your codec are now the correct ones.

14. Power the unit down.

7.2. Configuring the MAC address associated with the Ethernet interface.

From this menu the MAC address associated with the Ethernet interface can be edited;
because of the consequences this action could have, the addresses should only be edited if the
codec use situation requires it. The editing should be performed by highly qualified personnel or
under the supervision of AEQ authorized technical services, and always in possession of the
required network information.

1. From MENU

ETHERNET, check the IP address associated with the Ethernet

interface.

2. Power down the PHOENIX ALIO.
3. Connect PHOENIX ALIO to the PC from which you are going to perform the upgrading

process using a crossed cable.

4. Power up the PHOENIX ALIO.
5. Open the Internet Explorer web browser and, in the address bar, enter HTTP://<IP

address obtained in point 1>. Press ENTER and the main screen will be displayed.
Selecting the MAINTENANCE option will enable you to modify the MAC address of the
Ethernet interface of the unit.

«
...
69
70
71
72
73
...
»

Summary of Contents for PHOENIX ALIO




























































































Reviews:

No comments