AEM SM40 Installation And Operation Manual Download Page 29

Page: 29 / 31

UT12-000 Universal Encoder/Decoder

SM40 Installation and Operation Manual

May 15, 2012 Rev: 5.00

Page 3-13

ENG-FORM: 806-0100.DOTX

CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.

3.7.1 LAM

–

LA-M Radionetwork

CALL

SIGNAL

RESPONSE

DISPLAY

NOTES

FIXED TO UT12

UUUU__FF0FF

UUUUU

-CALL-: FF0FF

UT12 responds within 1100 ± 50

ms after last tone received

UUUU

CALL-: NO ID

FIXED TO UT12

GROUP CALL

UUU0__FF0FF

UU00__FF0FF

U000__FF0FF

No response from

UT12 on Group Call.

GroupCall FF0FF

These are the only three codes

that will access this receiving

UT12 for a group call

UT12 to

GROUP CALL

81099__M

MMM0__UUUUU

81099__M

MM00__UUUUU

81099__M

M000__UUUUU

GroupCall Sent

FIXED TO UT12,

ALARM CALL

C000___FF0FF

C400___FF0FF

No response from

UT12

**ALARM**

FF0FF

UT12 TO MOBILE

(Relay)

81099__M

MMMM__UUUUU

MMMMM

MOBILE ANSWER

MOBILE ID within 100 ms to 3

seconds

MOBILE to UT12

(Relay)

81099__U

UUUU__MMMMM

UUUUU

CALL-:MMMMM

UT12 ID within 750 ± 50 ms

Note: UT12 may/may not

receive base station relay code

81099

UUUU

CALL-: NO ID

UT12 to FIXED

890HH__FF0FF__UUUUU

Fixed unit responds with
a connect tone.

Carrier -

No carrier in 2 secs -

-FIXED CONNECT
-NO REPLY

UT12 determines that sequence

is from a fixed unit by third

tone = 0 and transmits the

home region first

STATUS CALL

890HH__820XX__UUUU

STATUS call works as per

3.4.2.7

UT12 to PSTN

890HH__819091__UUUUU

890HH__81093__UUUUU

Waiting for response-

No carrier after 10 secs-

Carrier within 10 seconds-

-Waiting
-DISCONNECT
-ENTER PHONE NO.

If LAM Phone Seq. Ends in

1: DTMF tones are transmitted

3: CCIR tone sequences are

transmitted (XEBXE)

CALL BREAKDOWN

819098

(UT12

button is pressed)

3.7.2 AFN

–

Air Force Radionetwork

CALL

SIGNAL

RESPONSE

DISPLAY

NOTES

FIXED TO UT12

UUUU

UT12 responds within

750 ± 50 ms

FIXED TO UT12
(group)

UUU0

UU00

No response from

UT12 on Group Call.

Only these two codes will access this

receiving UT12 on a group call.

UT12 TO MOBILE
(Relay)

MMMM

Mobile responds within 100 ms to 3 s

After end of last transmitted tone

UT12 to FIXED

FFFF

Fixed unit responds 100 ms to 3

seconds after last transmitted tone

If the fixed unit’s ID starts with an 8

there will not be a reply tone. See

section 3.2.2.1 for operation.

STATUS CALL

Status call works the same in AFN Network as in LAM.

UT12 to PSTN

PPPP

Waiting for response-

No carrier after 10 secs-

Carrier within 10 seconds-

-Waiting
-DISCONNECT
-ENTER PHONE NO.

PPPPP is the AFN Phone Code from

the config. Settings.

CALL BREAKDOWN

0200

(UT12

button is pressed)

UT12 to MIL PHONE

8XXXX

No Carrier-

-NO REPLY

Carrier-

-MIL PHONE CALL

Summary of Contents for SM40
































Search results

Summary of Contents for SM40

Reviews:

Related manuals for SM40

Brands by name

Popular brands

AEM SM40, Installation And Operation Manual

Search results

Summary of Contents for SM40

Reviews:

Related manuals for SM40

Brands by name

Popular brands