background image

9

AEM Air Intake System Warranty Policy

AEM

® 

warrants that its intake systems will last the life of your vehicle.  AEM will not 

honor this warranty due to mechanical damage (i.e.  improper installation or fitment), 

damage from misuse, accidents or flying debris.  AEM will not warrant its powder coating 

if the finish has been cleaned with a hydrocarbon-based solvent.  The powder coating 

should only be cleaned with a mild soap and water solution.  Proof of purchase of both 

the vehicle and AEM intake system is required for redemption of a warranty claim.
This warranty is limited to the repair or replacement of the AEM part.  In no event 

shall this warranty exceed the original purchase price of the AEM part nor shall AEM 

be responsible for special, incidental or consequential damages or cost incurred due 

to the failure of this product.  Warranty claims to AEM must be transportation prepaid 

and accompanied with dated proof of purchase.  This warranty applies only to the 

original purchaser of product and is nontransferable.  Improper use or installation, 

use for racing, accident, abuse unauthorized repairs or alterations voids this warranty.  

AEM disclaims any liability for consequential damages due to breach of any written or 

implied warranty of all products manufactured by AEM.  Warranty returns will only be 

accepted by AEM when accompanied by a valid Return Merchandise Authorization (RMA) 

number.  Credit for defective products will be issued pending inspection.  Product must 

be received by AEM within 20 days of the date RMA is issued.
If you have a warranty issue, please call (800) 992-3000 and our customer service 

department will assist you.  A proof of purchase is required for all AEM warranty claims. 

10-409

02/28/2013

Summary of Contents for 21-724










Reviews: