12
© 2021 AEM Performance Electronics
30-6053
APPLICATION NOTES
Description
Function
Pin
Make:
Acura/Honda
Spare Injector Drivers:
Injector 5
D1
Model:
S2000
Spare Injector Drivers:
Injector 6
B19
Years Covered:
2006–2008
Spare Injector Drivers:
Injector 7
D2
Engine Displacement:
2.2L
Spare Injector Drivers:
Injector 8
B16
Engine Configuration:
Inline 4
Spare Injector Drivers:
Injector 9
A12 or A13
Firing Order:
1-3-4-2
Spare Injector Drivers:
Injector 10
C11
N/A, S/C or T/C:
N/A
Spare Injector Drivers:
Injector 11
A14
Load Sensor Type:
MAP
Spare Injector Drivers:
Injector 12
A10
MAP Min:
0.32V @ -13.9 psi
Spare Coil Drivers:
Coil 7
A13*
MAP Max:
4.84V @ 10.94 psi
Spare Coil Drivers:
Coil 8
A22*
# Coils:
4 smart coils with built in ignitors
Boost Solenoid:
PW 2
D16
Ignition Driver Type:
0–5V Falling Edge trigger
Spare PWM Freq Driver:
PW 1
B15 or B23
# of Injectors:
4 (Inj 1–4)
EGT 1 Location:
EGT 1
A5
Factory Injectors:
360 cc/min saturated
EGT 2 Location:
EGT 2
D7
Factory Inj Resistors:
No
EGT 3 Location:
EGT 3
A30
Injection Mode:
Sequential
EGT 4 Location:
EGT 4
C5
Knock Sensors Used:
1 (Knock 1)
Spare 0–5V Input Channel:
ADCR03
A29
Lambda Sensors Used:
1 (O2 # 1, wideband sensor
required, original O2 sensor used
only for original check engine light)
Spare 0–5V Input Channel:
ADCR11
C6
Spare 0–5V Input Channel:
ADCR13
C24
Spare 0–5V Input Channel:
ADCR14
D8
Spare Low Side Output Driver:
Low side 1
A2
Idle Control:
Stock electronic throttle
Spare Low Side Output Driver:
Low side 2
C1
Main Relay Control:
Controlled by stock ECU
Spare Low Side Output Driver:
Low side 4
A6
Crank Pickup Type:
Hall Effect (3-wire)
Spare Low Side Output Driver:
Low side 5
A4
Crank Teeth/Cycle:
24 plus 2
Spare Low Side Output Driver:
Low side 7
A19
Cam Pickup Type:
Hall Effect (3-wire)
Spare Low Side Output Driver:
Low side 10
A18
Cam Teeth/Cycle:
4 plus 1
Spare Low Side Output Driver:
Low side 12
A8
Transmissions Offered:
Manual
Spare Low Side Output Driver:
Idle 2
A28
Trans Supported:
Manual
Spare Low Side Output Driver:
Idle 4
D5
Drive Options:
RWD
Spare Low Side Output Driver:
Idle 6
B17
Supplied Connectors:
N/A
Spare Low Side Output Driver:
Idle 8
B25
AEM Extension/Patch
Harness:
30-2986C (from vehicle harness)
VTEC High Side Driver:
High side 1
B12
Spare High Side Driver:
High side 2
B7
AEM Plug/Pin Kit:
35-2610
Spare High Side Driver:
Idle 1
D3
Spare High Side Driver:
Idle 3
A25
Spare High Side Driver:
Idle 5
B8
Spare High Side Driver:
Idle 7
B18
Spare Switch Input:
Switch 1
A32
Spare Switch Input:
Switch 2
D11
Spare Switch Input:
Switch 3
D12
Spare Switch Input:
Switch 5
C10
A/C Switch Input:
Switch 6
A27
WARNING:
*The Coil 7 and Coil 8 outputs are intended only for use with ignitors (or smart coils with built-in ignitors). Do not connect these
pins directly to 2-wire direct-fire ignition coils (a.k.a. ‘dumb’ coils); doing so will damage your EMS and void your warranty.
All switch input pins must connect to ground, the switch should not provide 12V power to the EMS because that will not be
detected as on or off. Connecting 12V power to the switch input pins may damage your EMS and void your warranty.
