AEG SR 4365 CD, Instruction Manual

Page: 32 / 58

English
32
Switch-off
The machine is switched off when the function selector switch
(18) is turned to the OFF position.The POWER (9) control
lamp goes off. Unplug the device.
NOTE:
After about 10 minutes without signal, the device switches
automatically to Standby. To use the device again, set the
function selector switch to the OFF position. Afterwards set
the switch again to the desired operating mode.
AUX IN socket
To connect analogue replay devices. Via this socket you can
also hear the sound of other playback devices such as MP3
players, CD players etc. through the loudspeakers.
1. Please connect the external device with a 3.5 mm stereo
jack plug to the AUX IN socket (back).
2. Set the function selector (18) to CD/AUX. The device
switches automatically to AUX IN operation.
3. Through the loudspeakers you can hear the playback of
the sound from the external device; with the VOLUME
control (17) you can change the volume. The CD buttons
do not have any function.
4. For the remaining procedure please see the operating
instructions of the external sound source.
NOTE:
Adjust the volume of the external device to a comfortable
level.
Listening to the Radio
1. Turn the function selector switch (18) to the RADIO posi-
tion.
2. Pull out the telescopic antenna (1). If necessary turn the
antenna to improve the radio reception.
3. Tune in the desired station with the station adjustment
knob TUNING (5).
Playing CDs
This is how you play a CD
NOTE:
If a cable is connected to the AUX jack, then this connec-
tion is preferred. Playback of CDs is only possible without a
connected AUX cable.
1. Turn the function selector switch (18) to the “CD/AUX”.
2. Open the CD compartment (3) by pulling the lid upwards
by the tab (4).
3. Insert an audio CD with the printed side facing upwards
on to the central cone so that the CD clicks into place
and then close the lid of the CD compartment.
4. The display shows “– –” and then the number of titles.
Press the PLAY/PAUSE button (6) to play the CD. The CD
will play from the first title. The current track is shown on
the display.
IMPORTANT NOTE:
Playing of CDs and CDRs in MP3 format!
The unit cannot play MP3s. The CD will rotate, but the
sound cannot be reproduced.
5. In order to remove a CD, please press the STOP button
(16), open the CD compartment and lift the CD out care-
fully.
Always keep the CD deck closed.
NOTE:
• If a disc is incorrectly inserted - or no disc has been
inserted - the symbol “– –” and the word “ ” appear
in the display.
• Please observe:
Many burning methods exist, as well as quality differ -
ences with CDs and burned CDs.
In addition, the music industry does not observe fixed
standards (copy protection).
Because of this, in rare cases there may be problems
with playback of CDs. This is not a malfunction of the
device.
Description of the CD buttons
PLAY/PAUSE (6)
You can briely interrupt and resume playback using this
button. The indicator lamp (11) will flash. Pressing again
continues playback. The indicator lamp is lit.
SKIP UP/SKIP DN (7/15)
When audio CD is playing:
With SKIP UP you can jump to the next or previous track etc.
• If the button is kept pressed down, the machine starts to
search through the tracks.
The SKIP DN button can be used as follows:
Press once = This starts the current track again from the
beginning.
Press twice = This jumps back to the previous track.
Press three times = This plays the song before etc. If the but -
ton is kept pressed down, the machine
starts to search through the tracks.
STOP (16)
The CD stops.
REPEAT/PROG (8)
When audio CD is playing:
Press once = the current track is repeated continuously.
The indicator lamp (10) flashes.
Press twice = the whole CD is played continuously. The
indicator lamp (10) is lit.