background image

careful they do not come in touch with

mobile parts or they are not squeezed.

Also be careful when the hob is put

together with an oven.

Make sure that the gas

supply pressure of the

appliance obeys the

recommended values. The

adjustable connection is

fixed to the comprehensive

ramp by means of a

threaded nut R 1/2". Screw

the parts and tighten

everything with teflon tape,

if necessary, to get the right

direction.

A

B

A.

End of shaft

B.

Elbow supplied with the appliance

Liquid gas

Use the rubber pipe holder for liquid

gas. Always engage the gasket. Then

continue with the gas connection.
The flexible pipe is prepared for apply

when:
• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting

edges or corners;

• it can be easily examined in order to

make sure its condition.

The control of preservation of the flexible

pipe consists in checking that:
• it does not show cracks, cuts, marks of

burnings on the two ends and on its

full length;

• the material is not hardened, but

shows its correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

WARNING!

When installation is

complete, make sure that

the seal of each pipe fitting

is correct. Use a soapy

solution, not a flame!

3.3 

Injectors replacement

WARNING!

The injector kit for gas

replacement is not provided.

Please call the Authorized

Service Center.

1.

Remove the pan supports.

2.

Remove the caps and crowns of the

burner.

3.

With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in

"Technical Data" chapter).

4.

Assemble the parts, follow the same

procedure backwards.

5.

Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

3.4 

Adjustment of minimum

level

To adjust the minimum level of the

burners:

1.

Light the burner.

2.

Turn the knob on the minimum

position.

3.

Remove the knob . 

4.

With a thin screwdriver, adjust the

bypass screw position (A).

www.aeg.com

8

Summary of Contents for HC412001GB





















Reviews: