AEG FAVORIT 60850 ViM User Information Download Page 34 | Manualshive

Page: 34 / 52

AEG FAVORIT 60850 ViM User Information Download Page 34

34

What to do if…

Remedying small malfunctions

Before you call the Customer Care Department, please check whether

–

you cannot remedy the fault yourself with the help of the following
fault table

or

–

whether it is caused by faulty, electrical connections and/or faulty
water connections.

In these cases the engineer must make you liable for the costs of the
Customer Service intervention even during the warranty period.
In the event of a fault, the light signal at floor level flashes.
If the acoustic signal is activated, warning tones sound if there are
faults.
If one of the following fault codes is displayed in the multi-display dur-
ing operation:

–

Fault code

Å 10

(Problems with water inlet),

–

Fault code

Å 20

(Problems with water drainage),

please have a look at the following table.
When the fault is remedied, press the button for the cycle that has
started. The cycle will continue.
With other fault codes (“

Å

” followed by a number):

–

Abort the dishwashing cycle.

–

Switch the appliance off and on again.

–

Re-set the dishwashing cycle.

If the fault is displayed again, please contact the Customer Care De-
partment and inform them of the fault code.

«
...
32
33
34
35
36
...
»

Summary of Contents for FAVORIT 60850 ViM





















































Reviews:

No comments