background image

11

11

CLEANING AND CHANGING HEPA FILTER

 WARNING

after each discharge cycle or if performance drops. Replace 

basis.

NOTE:

 Filter maintenance is important. Make sure the HEPA 

completely dry before reusing in the vacuum. We recommend 

in case of urgent use needed.

occur after you have checked for any obstructions in the hose 

or wand. Also, install a new collection bag.

INSTALLING AND CLEANING FOAM SLEEVE FILTER

See figure 11.

1.  Verify that no battery pack is inserted in the battery ports.
2.  Remove power head and place in upside down position.
3.  Carefully slide foam sleeve filter down over the filter cage 

making sure the hole is covered.

4.  Replace the power head on to the tank.

See figure 17.

1.  With the removed power head in the upside down position, 

carefully remove foam sleeve filter.

2.  Use a mild soap and water solution to wash foam sleeve 

filter and rinse with clean water.

3.  Allow filter to air dry before installing and using again.

CHANGING THE DUST BAG

When  the  collection  bag  is  3/4  full,  it  must  be  replaced. 

from the vacuum tank and can result in breakage and spills. 

When  collection  bag  becomes  3/4  full,  turn  off  vacuum  and 

slowly  remove  the  collection  bag  from  the  tank  until  the 

opening in the collection bag is clear of the tank.
Use  only  AEG  accessories  and  AEG  spare  parts.  Should 

components  need  to  be  replaced  which  have  not  been 

described, please contact one of our AEG service agents (see 

our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please 

state the Article No. as well as the machine type printed on 

the label and order the drawing at your local service agents 

or directly at:

Techtronic Industries (Australia) Pty. Ltd. 

PO Box 1065 

Mount Waverley VIC 3149 

Tel. no. 1300 361 505 

Australia

Techtronic Industries N.Z. Ltd

.

PO Box 12-806 

Penrose AUCKLAND 1642 

Tel no. 0800 279 624 

New Zealand

SYMBOLS

Safety alert

Regulatory Compliance Mark (RCM). Product 

meets applicable regulatory requirements.

Please  read  the  instructions  carefully  before 

starting the machine.

Do  not  dispose  of  electric  tools  together  with 

household  waste  material.  Electric  tools  and 

electronic  equipment  that  have  reached  the 

end  of  their  life  must  be  collected  separately 

and returned to an environmentally compatible 

recycling facility.

TROUBLESHOOTING

Problem

Possible Causes

Solution

Vacuum will not operate.

1.  No power supply.
2.  Tank full.

1.  Check if battery pack is properly inserted.
2.  Check if battery pack if charged.
3.  Empty tank.

Dust  comes  out  from  motor 

cover.

1.  The cartridge filter is missing or damaged.
2.  HEPA  cartridge  filter  is  not  installed 

correctly.

1.  Attach or replace cartridge filter.
2.  Check the HEPA catridge filter and install 

it correctly.

Reduced efficiency and motor/

speed vibration.

1.  There is a blockage in the nozzle, hose, 

or  the  tank  inlet.  The  cartridge  filter  is 

clogged by fine dust.

2.  Dust bag is full.

1.  Check  nozzle,  hose  and  tank  inlets  for 

blockage. Take off the filter and clean it. Or 

install a new cartridge filter.

2.  Replace the dust bag.

Summary of Contents for AP218E2-0













Reviews: