AEG A18FCN18GA Original Instructions Manual Download Page 15

Page: 15 / 20

QDLOHU*ULSWKHKDQGOH¿UPO\OHWWKHSURGXFWGRWKHZRUNDQGGRQRW

place second hand on top of product or near exhaust at any time.

Failure to heed this warning can result in serious personal injury.
Do not drive fasteners on top of other fasteners or with the product at an

RYHUO\VWHHSDQJOHDVWKLVPD\FDXVHGHÀHFWLRQRIIDVWHQHUVZKLFKFRXOG

cause injury.
Always check the work area for hidden wiring, gas lines, water lines,

etc., before using the product on such work area.
After using the product in the contact actuation mode, switch it back

to the full sequential mode.
The driving depth of the fastener may be adjusted beyond air

pressure. It is advisable to test the depth on a scrap workpiece to

determine the required depth for the application.

2QO\IDVWHQHUVPDWFKLQJWKHGHVFULSWLRQLQWKHSURGXFWVSHFL¿FDWLRQV

table can be used with this product. Using incorrect fasteners may

lead to jamming or other malfunctions.
Always remove the battery before adjusting the depth of drive.
Do not press the trigger while adjusting the depth of drive.

$OZD\VVHOHFWIXOOVHTXHQWLDO¿ULQJPRGHEHIRUHDGMXVWLQJWKHGHSWK

of drive.
Do not point the product towards yourself or anyone nearby when

adjusting the depth of drive.
The product will restart automatically if stalled. Switch off the product

immediately if it stalls. Do not switch on the product again while it

is still stalled, as doing so could trigger a sudden recoil with a high

reactive force. Determine why the product stalled and rectify this,

paying heed to the safety instructions.
Ambient temperature range for tool during operation is between 0°C

and 40°C.
Ambient temperature range for tool storage is between 0°C and

40°C.
The recommended ambient temperature range for the charging

system during charging is between 10°C and 38°C.

%HIRUH¿UVWXVHWHVWWKHQDLOHUIXQFWLRQZLWKVFUDSZRRG

7KLVZLOOHQVXUHFRUUHFWSHUIRUPDQFHRIWKHQDLOHU,IWKH

QDLOHUH[SHULHQFHVSHUIRUPDQFHLVVXHVUHLQÀDWHWKHDLUWDQN

IROORZLQJWKHLQVWUXFWLRQVJLYHQ

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING!

7RUHGXFHWKHULVNRI¿UHSHUVRQDOLQMXU\DQG

product damage due to a short circuit, never immerse your tool,

EDWWHU\SDFNRUFKDUJHULQÀXLGRUDOORZDÀXLGWRÀRZLQVLGHWKHP

&RUURVLYHRUFRQGXFWLYHÀXLGVVXFKDVVHDZDWHUFHUWDLQLQGXVWULDO

chemicals, and bleach or bleach containing products, etc., can

cause a short circuit.
Do not dispose of used battery packs in the household refuse or

by burning them. AEG Distributors offer to retrieve old batteries to

protect our environment.
Do not store the battery pack together with metal objects (short

circuit risk).
Use only System AEG chargers for charging System AEG battery

packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section of the

charger (short circuit risk).
Never break open battery packs and chargers and store only in dry

rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load

or extreme temperatures. In case of contact with battery acid wash

it off immediately with soap and water. In case of eye contact rinse

thoroughly for at least 10 minutes and immediately seek medical

attention.
Ambient temperature range for battery during use is between 0°C

and 40°C.
Ambient temperature range for battery storage is between 0°C and

20°C.

SPECIFIED CONDITIONS OF USE

The nailer is intended to drive nails in soft materials such as wood.

7KLVSURGXFWLVQRWVXLWDEOHIRU¿[LQJHOHFWULFFDEOHV

Do not use the product for any other purpose.

BATTERIES

Battery packs which have not been used for some time should be

recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of

the battery pack. Avoid extended exposure to heat or sunshine (risk

of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,

after used.
To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.

)RUEDWWHU\SDFNVWRUDJHORQJHUWKDQGD\V

• Store the battery pack where the temperature is below 27°C and

away from moisture.

• Store the battery packs in a 30% - 50% charged condition.

• Every six months of storage, charge the pack as normal.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods

Legislation requirements.
Transportation of those batteries has to be done in accordance with

local, national and international provisions and regulations.
• The user can transport the batteries by road without further

requirements.

• Commercial transport of Lithium-Ion batteries by third parties is

subject to Dangerous Goods regulations. Transport preparation

and transport are exclusively to be carried out by appropriately

trained persons and the process has to be accompanied by

corresponding experts.

:KHQWUDQVSRUWLQJEDWWHULHV

• Ensure that battery contact terminals are protected and insulated

to prevent short circuit.

• Ensure that battery pack is secured against movement within

packaging.

• Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice.

BATTERY PACK PROTECTION LI-ION BATTERY

The battery pack has overload protection that protects it from being

overloaded and helps to ensure long life. Under extreme stress the

battery electronics switch off the machine automatically. To restart,

switch the machine off and then on again. If the machine does not

start up again, the battery pack may have discharged completely. In

this case it must be recharged in the battery charger.

MAINTENANCE

Clean the product and guarding system with clean cloths or brushes.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should

components need to be replaced which have not been described,

please contact one of our AEG service agents (see our list of

guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state

the Article No. as well as the machine type printed on the label and

order the drawing at your local service agents or directly at:

7HFKWURQLF,QGXVWULHV$XVWUDOLD3W\/WG

PO Box 1065

Mount Waverley VIC 3149

Tel. no. 1300 234 797

Australia

7HFKWURQLF,QGXVWULHV1=/LPLWHG

PO Box 12-806