AEG 11210 Instruction Manual Download

Page: 32 / 33

- 31 -

CHECKING PERFORMANCE PROBLEMS – TROUBLESHOOTING

Problem

Probable cause

What to do

Fabric does not
move

- Feed teeth down
- Stitch length dial “0“ position
- Light presser foot pressure

- Raise feed teeth
- Set dial between 1 and 4
- Increase pressure

Breaking needle

- Incorrect insertion of needle
- Bent needle
- Fabric is being pulled
- Needle, thread and fabric do

not match

- Re-insert needle
- Replace needle
- Do not pull fabric

- Use correct needle and thread

Breaking upper
thread

- Faulty adjustment of zigzag

width

- Improper threading
- Tight upper thread tension
- Bent needle
- Scratches or nicks on bobbin

case

- Re-adjust zigzag width

- Re-thread machine
- Reduce upper thread tension
- Replace needle
- Polish or replace bobbin case

Breaking bobbin
thread

- Tight bobbin thread tension
- Incorrect insertion of needle
- Improper threading
- Lint or thread in bobbin case

- Reduce bobbin thread tension
- Re-insert needle
- Rethread machine
- Clean bobbin case

Machine
jamming

- Excessive tension
- Presser foot pressure too

strong

- Needle, thread and fabric do
not match

- No oil

- Re-adjust tension
- Change pressure accordingly

- Reduce proper needle and

thread according to type of
fabric

- Oil moving parts

Puckering

- Tension too tight
- Sewing foot pressure too

strong

- Incorrect fabric, needle,

and thread

- Reset
- Reduce sewing foot pressure

- Use correct fabric, needle

and thread

Summary of Contents for 11210


































Search results

Summary of Contents for 11210

Reviews:

Related manuals for 11210

Brands by name

Popular brands

AEG 11210, Instruction Manual

Search results

Summary of Contents for 11210

Reviews:

Related manuals for 11210

Brands by name

Popular brands