AEA PAKRATT PK-232 Page 33 Operating Manual Download | Manualshive

Page: 33 / 199

background image

USER'S GUIDE

INSTALLATION

PK232UG Rev. B 9/86

2-15

33

10. Type

Q

to "Quit" (exit) the calibration routine.

You've now set your FM transmitter's deviation to an approximate level which will be
adequate for initial operation.

11. With your radio in the receive mode, open the squelch control so that a steady hiss

or noise is heard in the speaker.

12. Set the PK-232's THRESHOLD control to the "12-o'clock" position.

13. Set the receiver's volume control so the DCD LED on your PK-232 just lights with the

receiver unsquelched.

This is the approximate proper level for best receive performance from your PK-232's
modem.

14. Reset your transceiver's squelch control for normal operation.

2.7.2

SSB Installation and Adjustment

Installation and adjustment of your PK-232 with SSB radios is usually simpler and more di-
rect than with the FM equipment. You'll use the same kind of cables and connectors that
you use with your FM gear.

Digital modes with SSB radio require some different settings of the radio's operating con-
trols for proper AMTOR and packet operation. Be sure to observe the following precau-
tions:

o

Set VOX to

OFF

.

o

Set speech compression to

OFF

.

o

Set AGC to

FAST

(if available).

o

Disconnect the ALC cables between your SSB radio and any external RF amplifier
you wish to use in AMTOR or Packet-Radio service.

Remember – Baudot, ASCII RTTY and Node B (FEC) AMTOR are continuous key-down
conditions –

your radio's duty cycle is 100 %

for the duration of each transmission. If

your SSB radio isn't designed for continuous full-power operation,

you must operate

your radio at reduced output power

. Consult the manufacturer's specifications for de-

tails on the operating duty cycle.

NOTE:

Make all connections with all power off. If your SSB radio has a phone patch
input  and  external  PTT  connections,  the  PK-232's  AFSK  output  can  be  con-
nected to those input jacks, leaving the microphone jack for normal service.
However,  some  microphones  are  connected  at  all  times  –  regardless  of  the
PTT line's state. In this case, remove the microphone from the input to pre-
vent  inadvertent  loading  of  the  audio  input  circuit.  If  the  phone  patch  jack
has  a  series  isolating  resistor,  your  microphone  can  remain  connected.

1. Connect your PK-232 and SSB radio as shown in Figure 2-2.

2. Turn on your PK-232 and your computer and start your terminal program.

3. Connect your SSB radio to a dummy load.

«
...
31
32
33
34
35
...
»

Summary of Contents for PAKRATT PK-232








































































































































































































Reviews:

No comments

Related manuals for PAKRATT PK-232

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: IAI Pages: 5

Brand: Harmonic Drive Pages: 85

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brand: ZKTeco Pages: 10

Brand: ZKTeco Pages: 121

Brand: ZKTeco Pages: 12

Brand: ZKTeco Pages: 6

Brand: ZiLOG Pages: 12

Brand: DAQ Pages: 63

Infi 90 IMSPM01

Brand: Bailey Pages: 52

Brand: Water Specialist Pages: 36

Brand: J+J Pages: 6

Brand: H3C Pages: 48

Brand: Xantech Pages: 12

Brand: FAAC Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands