background image

17 

 

5. TROUBLE SHOOTING 

Situation 

Solution 

Fault 

Code 

Fault Event 

01 

Over charge current 

1.

 

Restart the charger. 

2.

 

If the problem remains, please contact your 

installer. 

02 

Over temperature 

1.

 

Keep the charger in the cool environment. 

2.

 

If the problem remains, please contact your 

installer. 

03 

Battery voltage under 

1.

 

Check the battery wire connection. 

2.

 

If the wire connection is ok, please contact your 

installer. 

04 

Battery voltage high 

1.

 

Reconnect the battery to the charger. 

2.

 

If the problem remains, please contact your 
installer. 

05 

PV high loss 

1.

 

Please check the voltage of the solar panel, it 

should be less than 140V.   

2.

 

If the voltage is ok, please contact your installer. 

06 

Battery  temperature 
too low 

1.

 

Check your remote temperature sensor and 

your battery ambient temperature. 

2.

 

If the problem remains, please contact your 

installer. 

07 

Battery  temperature 
too high 

1.

 

Check your remote temperature sensor and 

your battery ambient temperature. 

2.

 

If the problem remains, please contact your 

installer. 

No display in LCD screen. 

1.

 

Check battery wire connection. 

2.

 

Push the button, if the problem remains, please 
contact your installer. 

www.

ADVICE

.co.il

e-mail:advice@advice.

co.il

Summary of Contents for ASC-MPPT-3000




















Reviews: