background image

www.AdventistSat.com 

          

 

      

               Toll Free 866-552-6882

13

Roof Mount

Wall Mount

Ground Post Mount

Dish Mounting Options

 

We recommend ground mounting the dish on 
a  1  5/8”  heavy  wall  galvanized  post  set  in 

cement. Attach a bolt or muffler clamp to the 

bottom of the post to prevent the post from 
twisting in the hardened cement. These items 
are readily available at any hardware store. 
Filling  the  post  with  a  wet  cement  mixture 
will provide greater rigidity. The post must 
be  perfectly  plumb,  level  on  all  sides. 
Posts  standing  higher  than  7  feet  should 
be  stabilized  to  prevent  movement  during 
high winds.  The post should be installed in 
advance of the install as the cement can take 

The AdventistSat system includes a heavy duty universal wall / roof 
post  mount. This  mount  can  be  attached  at  almost  any  angle  and 
provides a stable secure mount even in high wind regions if properly 
attached.  If this universal post mount is used, the included tripod 
legs 

MUST

 be installed. The universal post will fail under moderate 

wind load if the tripod legs have not been installed to support the 
larger wind load area of a 36” dish. The dish and mount are designed 
to  remain  operational  in  winds  up  to  80+  mph  and  survive  wind 
gusts over 110+ mph. 

24 - 48 hours to set. Do not install the dish on a wooden 4” x 4” post 
or on a tree. The grain of the wood will twist during dry and rainy 
seasons causing the dish to swing off of the satellite causing reduced 
or loss of signal. Take proper precautions to protect the dish from 
being bumped during yard care or damaged by children at play. 

Failure to install the tripod legs will result in a 
charge back to the professional installer. 

 

Summary of Contents for Fortec Mercury II








































Reviews: