Advantech XR5i v2 User Manual Download Page 34

Page: 34 / 34

10. CUSTOMERS SUPPORT

10. Customers Support

You can find current information about this product on our website:

Upkeep-advices:

•

The SIM-card must be handled carefully as with a credit card. Don’t bend, don’t scratch
on this and do not expose to static electricity.

•

During cleaning of the router do not use aggressive chemicals, solvents and abrasive
cleaners!

Advantech B+B SmartWorx s.r.o. hereby declares that the router narrated in this user’s guide
fits all basic demands of directive 1999/5/EC (R&TTE).

Router fits values of coefficient SAR defined by association ICNIRP and values of "About
protection of health before non-ionized radiation".

Declaration of Conformity was issued and it is possible to find it on the Advan-
tech B+B SmartWorx website (

www.bb-smartcellular.eu/download

) in respective

product category or is available on request from producer.

Summary of Contents for XR5i v2



































Search results

Summary of Contents for XR5i v2

Reviews:

Related manuals for XR5i v2

Brands by name

Popular brands

Advantech XR5i v2, User Manual

Search results

Summary of Contents for XR5i v2

Reviews:

Related manuals for XR5i v2

Brands by name

Popular brands