Advantech XR5i v2 User Manual Download Page 29

Page: 29 / 34

7. TECHNICAL PARAMETERS

7. Technical Parameters

7.1

Basic parameters

XR5i v2

Temperature range

Function
Storage

-40

◦

C to +75

◦

-40

◦

C to +85

◦

Humidity

Operating
Storage

0 to 95 % relative humidity non condensing
0 to 95 % relative humidity non condensing

Altitude

Operating

2000 m / 70 kPa

Degree of protection

IP30

Supply voltage

9 to 36 V DC

Consumption

Idle
WiFi Com.
Full Com.

1.6 W
1.9 W
to 2.5 W

Dimensions

42 x 76 x 113 mm (DIN lišta 35 mm)

Weight

XR5i v2 – 150 g
XR5i v2 SL – 280 g

User interface

ETH
USB
PORT1
PORT2

Ethernet (10/100 Mbit/s)
USB 2.0
Ethernet (10/100 Mbit/s)
On customer’s request

Table 11: Basic parameters

7.2

Standards and regulations

The router complies with the following standards and regulations.

Standards and regulations

EMC

ETSI EN 301 489-1 v1.9.2

Safety

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

Table 12: Standards and regulations

Summary of Contents for XR5i v2



































Search results

Summary of Contents for XR5i v2

Reviews:

Related manuals for XR5i v2

Brands by name

Popular brands

Advantech XR5i v2, User Manual

Search results

Summary of Contents for XR5i v2

Reviews:

Related manuals for XR5i v2

Brands by name

Popular brands