manualshive.com logo in svg

Advantech WISE-S100, User Manual

Share
Download
Advantech WISE-S100 User Manual Download Page 20

WISE-S100 Series User Manual

12

4.1

Operation Mode

There two different operation modes of WISE-S100 to pair with different device. One

is  Modbus  RTU  mode  and  another  one  is  serial  bus  mode. The  default  operation

mode  of  WISE-S100  is 

Serial  Bus  Mode

  for  pairing  with  WISE-4200/4400/4600

series, WiFi or LPWAN IoT Wireless Modular I/O.
Please follow below steps if you intend to use WISE-S100 to pair with WISE-4051,

2.4G WiFi IoT Wireless Modular I/O or any other Modbus master device.

Step 1.

Download WISE Studio

Please change to Modbus mode via WISE Studio (WISE Studio version needs to be

1.01.01 (B05) or above).

Step 2.

Operation Mode Change

The  way  to  access  WISE-S100  in  Serial  Bus  Mode  through  WISE  Studio  when

switching into Modbus Mode:
- PC < --- > ADAM-4561 or any other USB to RS-485 converter < --- > WISE-S100

Step 3.

Check the LED Indicator

The LED indicator will be on when WISE-S100 is powered on.
- Serial Bus Mode: LED indicator will be on for 5 secs the go off for power saving

when pairing with WISE-4200/4400/4600 LPWAN IoT Wireless Modular I/O.
- Modbus Mode: LED indicator will be on constantly.

Step 4.

Serial Bus Mode

Serial Bus Mode 

only used to 

pair with WISE-4200/4400/4600 series.

Please enter into the main page of WISE-S100 via WISE Studio.

Summary of Contents for WISE-S100

































Reviews:

No comments

Brands by name

Popular brands

Load more brands