manualshive.com logo in svg

Advantech WISE-4470 Series, User Manual

Share
Download
Advantech WISE-4470 Series User Manual Download Page 40

WISE-4471 Series User Manual

32

Diagnostician

Since different devices will have different response times, the WISE-4471 provides a
diagnostics function for testing the response time of each rule. This is intended to
reduce the scan interval. You can refer to the response time on this page when con-
figuring the 

Scan Interval

 in 

Rule Setting

 pages. You can reset the test result on this

page by clicking 

Reset Response Time

.

4.2.7

System Configuration

Network Application

Host Idle (timeout sec): Decides the availability of the TCP connection between 
the host controller and WISE. MCU-based WISE modules support four TCP 
connections at the same time for visiting users. It means WISE can be visited by 
four TCP hosts at the same time, and is not able to connect a fifth host. In this 
case, if one of the hosts stops communicating with the WISE module for longer 
than the configured host idle time, default 720 seconds, for example, the WISE 
module will close the TCP connection with the host.

Communication WDT: After configuring Host Idle time, and will be triggered 
when all TCP connections are closed. This includes all hosts which visit WISE 
and also the communication between remote servers like private servers. Once 
the WDT is enabled, it will trigger systems events like FSV of output channel or 
system log. 

Communication WDT trigger FSV: Decide whether FSV of output channel will 
be triggered by communication WDT.

Reboot Interval: Decide the time interval in minute to reboot WISE module when 
WISE module is not able to connect to cellular base station. 

RF Reset Interval: Decide the time interval in minute to reset the RF module in 
WISE module when WISE module is not able to connect to cellular base station. 

Summary of Contents for WISE-4470 Series



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands