manualshive.com logo in svg

Advantech WISE-4470 Series, User Manual

Share
Download
Advantech WISE-4470 Series User Manual Download Page 4

WISE-4471 Series User Manual

iv

Technical Support and Assistance

1.

Visit the Advantech web site at www.advantech.com/support where you can find 
the latest information about the product.

2.

Contact your distributor, sales representative, or Advantech's customer service 
center for technical support if you need additional assistance. Please have the 
following information ready before you call:

–

Product name and serial number

–

Description of your peripheral attachments

–

Description of your software (operating system, version, application software, 

etc.)

–

A complete description of the problem

–

The exact wording of any error messages

Warnings, Cautions and Notes

Document Feedback

To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advan-
tech.com

Package List

Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.

WISE-4471-S250 module x 1

 Mounting bracket x 1

 Quick startup manual x 1

 China RoHS declare x 1

Warning! Warnings indicate conditions, which if not observed, can cause personal 

injury!

Caution! Cautions are included to help you avoid damaging hardware or losing 

data. e.g.There is a danger of a new battery exploding if it is incorrectly 
installed. Do not attempt to recharge, force open, or heat the battery. 
Replace the battery only with the same or equivalent type recom-
mended by the manufacturer. Discard used batteries according to the 
manufacturer's instructions.

Note!

Notes provide optional additional information.

Summary of Contents for WISE-4470 Series



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands