Advantech TREK-753 User Manual Download Page 22 | Manualshive

Page: 22 / 73

background image

TREK-753 User Manual

14

3.1 Overview of Hardware Installation & Upgrading

The Mobile Data Terminal consists of a industrial computer that is housed in a rugge-
dized aluminum enclosure. Any memory module or storage maintenance or hard-
ware upgrades can be completed after removing the rear side RAM door/ Side cover,
or remove the front panel to install.

3.2 Installing the Storage Device and SIM Card

TREK-753 has a side door and user can install SIM card and storages (CF or SD
card) easily. CF card is the main bootable storage which has OS pre-installed from
Advantech. CF slot with a ejector (on the top side) then you can press and CF
ejected from socket. SD card as a secondary storage in TREK-753, system is NOT
allowed boot up from SD.

Note!

Please do NOT paste any sticker or label on CF and SD , it might be
jammed and not able to ejected from slot/socket.

«
...
20
21
22
23
24
...
»

Summary of Contents for TREK-753










































































Reviews:

No comments

Related manuals for TREK-753

Brand: Compaq Pages: 34

Brand: Acer Pages: 5

Brand: Supoin Pages: 12

1200 - Cell Phone 4 MB

Brand: Nokia Pages: 14

1200 - Cell Phone 4 MB

Brand: Nokia Pages: 132

1200 - Cell Phone 4 MB

Brand: Nokia Pages: 77

Brand: HandHeld Pages: 12

Brand: Honeywell Pages: 64

Brand: ACD Pages: 84

Brand: SHC Pages: 106

Brand: Belgravium Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands