Advantech TREK-753 User Manual Download Page 18 | Manualshive

Page: 18 / 73

background image

TREK-753 User Manual

10

2.2 Installation Procedures

When you installing TREK-753, the first step will be connect the car power and igni-
tion correctly. TREK-753 power cable is designed to connect car battery directly.
TREK-753 can be switched ON/OFF by the car ignition signal or its power button
both.

2.2.1 Connecting the Power Cord

Connect the three pin waterproof power cord to the DC inlet of TREK-753. On the
open-wire end, one pin is reserved for positive voltage and is marked "+" which
needs to be connected to the car power "+" side; one pin is reserved for ground and
is marked "-"; which needs to be connected to the car power "-" side. And, one pin is
reserved for the ignition signal with an “ignition” mark. There's independent "Shield"
pin in power cable, please fixed its O-ring which besides of power connecter of
TREK-753.

Connector : DECA Switchlab ME050-50803
Mating connector: MC101-50803-3Y

Figure 2.5 Power connector photo

Note!

TREK-753 power input support 12V/24V & 48V DC input. The default
setting is for 12V or 48V (option board) only. If customer needs 24V DC
input, please contact regional sales or distributors to customized in
advance.

Note!

The Fuse for 12V/24V (10A) system and for 48V (5A) in power cable are
different. Please check the fuse in your power cable before system
power on.

Note!

Ignition on/off setting: The TREK-753 supports an ignition on/off function
so that you can power on/off the TREK-753 via the ignition signal/volt-
age and connect the TREK-753 vehicle ignition switch.

«
...
16
17
18
19
20
...
»

Summary of Contents for TREK-753










































































Reviews:

No comments

Related manuals for TREK-753

Brand: Intermec Pages: 2

Brand: Speedata Pages: 10

Brand: Opticon Pages: 7

Brand: E-TEN Pages: 260

Brand: Opticon Pages: 105

Brand: Falcon Pages: 68

Brand: Janam Pages: 54

MTM800 Enhanced

Brand: Motorola Pages: 54

Brand: Motorola Pages: 321

Brand: Motorola Pages: 88

Brand: Motorola Pages: 2

Brand: Motorola Pages: 192

Brand: Motorola Pages: 120

MOTOTRBO MC1000

Brand: Motorola Pages: 71

Brand: Motorola Pages: 328

Brand: Motorola Pages: 78

Brand: Motorola Pages: 268

Brand: Toshiba Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands